Discovering Plumbing Basics is Important When Installing a Bathtub
Discovering Plumbing Basics is Important When Installing a Bathtub
Blog Article
This post in the next paragraphs pertaining to A Step-by-Step Guide to Installing a Bathtub is absolutely enlightening. You should investigate it.
Mounting a bathtub isn't precisely brain surgery, but it does call for strong plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately difficult task. If the old bathtub is conveniently available, the project can move rapidly; if you have to open up a wall to get rid of the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the brand-new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is far better to think about employing one prior to you start. Opportunities are you may require a specialist plumber to make tube links.
This post will aid you set up a new bathtub in your bathroom if you have actually already purchased a new bathtub and don't require to change the plan of your previous water pipes.
Your devices and also product checklist must comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of removing the existing taps can be quite bothersome due to the restricted access that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the staying water that will originate from the pipes. Once the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washing machines are in location in between the faucet as well as the sink. Protect the tap in position with the producer provided backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the needed position. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the tub up until the level reviews degree.
To set up taps, fit all-time low of the outermost versatile faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Turn on the water supply and examine all joints and brand-new pipework for leaks and tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
Lastly, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the bath tub must wait till the bath tub has actually been utilized at the very least when as this will settle it right into its last placement.
Preparing for the Installation
Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final placement.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, leading to problems with wetness and possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is advisable to fit the floor tiles using waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid reader on How to Install a Bathtub Yourself, I was thinking sharing that excerpt was beneficial. So long as you enjoyed our post plz remember to share it. Thank-you for your time invested reading it.
Request Service Report this page